PowerBox 6pro NCore

PowerBox 6pro NCore

In stock
Delivery period: 10 working days

PowerBox 6pro NCore with Hypex DLCP digital signal processor. 

  • All you need between your music source (CD, vinyl, BluetoothAP, SOONOS;......) and your speakers
  • PowerBox = Preamp & ADC & DSP & 6 DACs & 6 Hypex ncore_neg power amplifiers
  • Tailored performance: 2x100W, 2x125W, 2x250W, all 2Ohms capable!
  • Slim & quiet, fan-less design. Massive 3mm full aluminum case with stainless steel front plate. Dimensions ca 44 x 36 x 5,5 cm
  • Professional high current SpeakON output: Two SpeakONs replace 12 (!) “banana” plugs
  • High End Hypex DSP with carefully designed clock-, DAC- and analogue output stages.
  • Balanced signal from input to output, remote volume control.
  • LXspeaker owners get preloaded filter sets (LXmini, LXmini+2, LXstudio). LX521.4 needs two of these PowerBoxes, a MASTER  and a FOLLOWER unit.
  • IN: analog balanced XLR, digital RCA, optical, AES XLR & RJ45, USB for individual filter, gain, delay and inv. programming!
  • Free Hypex Filter Design software for any speaker project.

LX521.4s eight channels are supplied by one PowerBox per side. They work in a master-follower-fandem. MASTER-PowerBox and FOLLOWER-PowerBox are interconnected by a CAT6 or CAT7 network cable (up to 10m). Via this cable, the MASTER sends the (unfiltered) digital music signal and control commands to the FOLLOWER.

Details can be found here


Analogue input
The  DLCP  has  two  (stereo)  analogue  balanced  audio  inputs.  The  analogue  input  signal  is  buffered and amplified by a single-stage, fully differential programmable gain amplifier and then converted to digital by the ADC. The ADC is always directly clocked by the on-board oscillator, a low noise Colpitts oscillator with a locally regulated supply, causing less jitter. After the analogue to digital conversion the signal is processed by the DSP.


Digital input
The  DLCP  contains  four  separate  digital  inputs,  permitting  the  use  of  different  interconnection standards (AES/EBU and S/PDIF). Optimal clock quality is insured by routing the clock through separate IC’s from the data signals, and by local regulation of all supplies on the AES input circuit.  

Incoming AES / S/PDIF is send to the DSP through an asynchronous sample rate converter (ASRC) to reduce jitter.  
When the input is set to “Auto detect”, the ASRC chip scans its inputs for whichever digital signal is present. The input source is automatically switched to digital when present, using the priority described below. If the digital audio source is removed, the input will be automatically switched back the last chosen analogue input.  


Digital output
The DLCP contains two separate digital outputs, AES/EBU and S/PDIF. The selected digital input is directly send to both digital outputs. (Without filtering)


The DSP filtering can be changed by Hypex Filter Design (HFD) software. The digital outputs from the DSP are fed to the DACs. The DAC chip receives data from the DSP and clock either from the crystal oscillator or from the digital input section. The digital signal is then converted to analogue by the DAC. The post filter is executed twice, providing a balanced load to the  DAC and delivering a high output level to the power amplifier.


This is a high power device (more than 1000W) for professional use acc EN 61000-3-2 (Class A). Its connection to the electric network may require approval by the local electricity supplier.



1) What ist the maximum CAT 6 cable length between Master and Follower?
Master and Follower (last follower in achain of followers) must have max 10m cable inbetween.

2) Autodetect does not react on switching digital sources on/off. Why?
Probably, more than one active digital source is connected. Be aware, that even digital sources in "standby" may send an erroneous "zero" signal with no music content. Switch off and/or unplug all unused digital sources. Additionally: recycling from/to "autotetect" may re-establish source selection according hierarchy (see DLCP manual). 

3) After several hours of playing, PowerBox ocassionally does not react on volume commands. Despite changing front panel volume indication.
Recycle PowerBox Master und Followers main switch (30 sec between on and off)). This restores normal operation.


Selection: PowerBox 6pro NCore

Product no. function Price
PoBox6-M Master
PoBox6-F Follower


Product Note Price
LX521 - The Reference LX521 - The Reference
EarFood Artistic Fidelity Isolator & Reclocker EarFood Artistic Fidelity Isolator & Reclocker

Product data sheet

LXmini kit LXmini kit
Sommer SC-Mercator CAT.7 PUR Sommer SC-Mercator CAT.7 PUR
LXstudio LXstudio
LXsirius+2 LXsirius+2
LXmini+2 upgrade LXmini+2 upgrade
Display accessory details

Customers who bought this product also bought

RCA-XLR adaptor cable, 1m
Sommer SC-Mercator CAT.7 PUR

Browse these categories as well: PowerBox, LXpower